Cooper Security M2000 Dokumentacja Pobierz pdf (Strona 15)

M2000 Installation Instructions 15

LEDs

The LEDs (see Figure 2) have the following meanings:

• LED1 (heartbeat) – Flashes once per second to

indicate that the panel is operating. The LED

flashes rapidly after a reset.

• LED2 (network 1 fuse) – Monitors the polyfuse for

network 1. When illuminated, the LED indicates

that the 12V supply to network 1 is open circuit.

• LED3 (network 2 fuse) – Same as LED2, but for

network 2.

• LED4 (PSTN) – Illuminates when there is activity on

the PSTN port.

• LED5 (power) – Illuminates when the panel is

energised (either from the AC input or from the

battery).

• LED6 (12V output fuse) – Monitors the polyfuse

protecting the 12Vdc output from the terminal

block labelled "16" on Figure 2.

• LED7 (Bell output fuse) – Monitors the polyfuse

protecting the bell output labelled "9" on Figure 2.

• LED8 (relay 1 status) – Illuminates when relay 1 is

energised.

• LED9 (relay 2 status) – Illuminates when relay 2 is

energised.

• LED10 (transistor output 3 status) – Illuminates

when transistor output 3 is active.

• LED11 (transistor output 4 status) – Illuminates

when transistor output 4 is active.

• LED12 (strobe output status) – Illuminates when

the strobe output is active.

• LED13 (bell output status) – Illuminates when the

bell output is active.

• LED14 (transistor output 5 status) – Illuminates

when transistor output 5 is active.

Polyfuses

The PCB contains the following automatically-

resettable polyfuses. Note that to reset a polyfuse, the

load must be removed completely.

• F1 – Battery load circuit (the on-board circuit that

periodically monitors the health of the battery).

• F2 – Network 1 12Vdc output.

• F3 – Network 2 12Vdc output.

• F4 – Extension loudspeaker.

• F5 – 12Vdc output from the 12V terminals on the

terminal block labelled "16" on Figure 2.

• F6 – Bell output on the terminal block labelled "9"

on Figure 2.

Electromagnetic Compatibility

When used as intended this product complies with

EMC Directive (89 /336 /EEC). Any modifications other

than those stated in this manual, or any other use of

this product may cause interference and it is the

responsibility of the installer to comply with the EMC

and Low Voltage Directives.

Technical Specifications

Environmental Class II

Security EN50131-1 or PD6662 Grade 1, 2

or 3. See page 14.

Mains Supply: 145mA @ 230Vac±10%, 50Hz

PCB Power Supply: 13.65VDC, 1.5A

A maximum of 750mA is available

for the control panel PCB and

other devices (excluding battery

recharge)

Standby Battery: 12VDC, lead-acid.

See page 14 for further details.

Charging limit: 750mA

Recharge time: 24 hrs max. for 17AH battery

Zones: 8 on-board zones, expandable to

264

Network 1 or 2: Max of 16

MSNodes/MRNodes/MSPSUs, 5

keypads/LEC2s, 4 MIDNodes, or 2

IDNodes per network

Additional ports: Engineer's keypad port

USB and RS232 ports to PC

Printer (RS232) port

PSTN/RJ11 for phone connection

Output module port

Relay Outputs: 2 voltage-free changeover

1A max @ 24Vac or 24Vdc

Transistor Outputs: 2 Switched -ve @500mA

1 Switched +ve @500mA

Digi Outputs 1-16: Source 5mA in 12V condition

Sink 100mA in 0V condition

Selectable output sense

REN Value: 0.2

Speaker Output: 16 Ohms

Bell Trigger: Switched -ve @500mA

Strobe Trigger: Switched -ve @500mA

Mains Input Fuse: T315mA 250V 20mm

Dimensions: 384(W), 312(H), 95(D) mm

Material: 1.2mm mild steel

Weight: 4.9 Kg

Environment: -10 to 40°C

Humidity 0 to 75% RH, non-condensing.

1 2 ... 10 11 12 13 14 15 16

Komentarze do niniejszej Instrukcji

Brak uwag

Cooper Security M2000 Dokumentacja Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security M2000