Cooper Security 9751 Przewodnik Instalacji Strona 82
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4. Programming
76 496792
If the keypad display shows “Custom” when you enter Command 143 then
<Downloader> has been used to program this Command.
Plug by Communicator Outputs (Commands 151 to 158)
The main circuit board of the control unit provides eight programmable
outputs that can be used to control a plug-by communicator. The outputs can
be connected to the communicator by an twelve-way wiring harness provided
with the control unit. See “3. Installation - Fitting a Plug-by Communicator” for
details of the wiring harness.
Commands 151 to 158 allow you to assign one of several channels to each
output. Command 151 controls output 1, 152 output 2, and so on up to
Command 158 which controls output 8. Each Command has the same
options, as follows:
00 Not used 11 AC Fail
01 Fire 12 Tamper Alarm (Day tamper)
02 PA 13 Open
03 Burglar 14 Close
04 Open/Close 15 Zone Omitted
05 Alarm Abort 16 Medical Assistance
06 Technical Alarm 17 Key Box
07 Alarm Confirmation 18 Anti Mask
08 RF Low Battery 19 Smoke Detector
09 Supervision Loss 20 Comms Acknowledge (See Note)
10 RF Jamming 21 Battery Fault
Note: 1. If the control unit is using Fast Format signalling, and has sent a Burg to the
ARC, then the control unit activates the output pin assigned to Comms Ac-
knowledge when the ARC returns a Comms Acknowledge signal. (Use Com-
mand 101 to enable comms.)
2. The control unit delays reporting/loging either mains loss, or exiting engi-
neering with mains loss, by 15-18 min (chosen randomly). If you chose a
Scandinavian default in Command 0 then the control unit waits at least 60
minutes before reporting.
Confirmation Timer (Command 160)
Note: Enable Alarm Confirmation (Command 89) to access this Command.
This Command controls a timer. The timer starts when an alarm is triggered
for the first time. If a second alarm is triggered before the timer expires then
the control unit transmits a confirmed alarm to the ARC. You can set the
timer to any value in minutes between 1 and 999. For DD243: 2002 compli-
ance set confirmation time to default (=30 mins).
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security 9751
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji