Cooper Security 9751 Przewodnik Instalacji Strona 85
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4. Programming
496792 79
ACPO DD243: 2002 Compliance
Please study this section If you are installing an intruder alarm system in
England, Wales and Northern Ireland which has remote signalling, requires
the local Police Authority to issue a URN (Unique Reference Number) and
you have chosen to use “Sequential Alarm Confirmation” to comply with
DD243: 2002.
For installers in Scotland, the ACPOS Intruder Alarm Systems policy docu-
ment is now published, and it states: “confirmation technology (BS
DD243:2002 applies) is desirable for newly installed systems but is not
mandatory in terms of this policy. Police response to line cuts will be at the
discretion of individual forces”. Cooper Security Ltd. therefore recommend
that systems in Scotland are installed to comply with DD243:200, and install-
ers obtain copies of the ACPOS policy from their local Police.
Note: The installed system will only fully comply with the requirements of DD243:
2002 if it has been designed in accordance with this section.
Please use the following recommended Commands to ensure that the
installation is correctly programmed.
Recommended Programming Commands
Command 33 – System Reset = 1 = Engineer Reset. In addition various
other forms of reset can be used such as RedCARE reset or Anti-code (if the
CSID code has been programmed into the panel).
Commands 81, 82, 83, 84 – Output types. There are three new output types
that you can use to indicate the status of the system: Alarm Confirm, Set
Complete and Unset Complete.
Command 89 – Alarm Confirmation = 1 = enabled.
The following Commands can only be accessed if you have enabled
Alarm Confirmation.
Command 48 – Lockout Keypads During Entry = 1 = Yes. Use this option to
comply with section 6.4.5.
Command 160 – Confirm time = 30 (default).
Command 161 – Internal Sounder = Sounder on confirmed/unconfirmed
alarm.
Command 162 – External Sounder = Sounder on confirmed/unconfirmed
alarm.
Command 163 – Confirm After Entry = 0 = When a user starts the entry
timer then the control unit disables alarm confirmation. Use this option to
comply with sections 6.4.3, 6.4.4 and 6.4.6.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security 9751
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji