Cooper Security 9751 Przewodnik Instalacji Strona 87
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
496792 81
5. Testing
5. Testing
Reading the Log (Command 90)
The control unit keeps a 250 event log of recent events. Each event is
represented by a short text message, shown below and on the next page. To
review the event log, make sure the system is in programming mode, then:
1. Key in 90 .
The display shows the most recent event in the log. For a list of the log
messages see below.
2. Key in 1 to show earlier events or 3 to see more recent events.
3. Press to toggle between the event message and the event time.
4. Press to leave the log.
The table below and on the next page shows all the messages that can
appear in the event log. The left hand column shows the messages that
appear on a keypad display. The right hand column gives a brief explanation.
Note that neither the Installer nor the user can erase the log.
In the log user codes are represented by numbers as follows:
U00 Installer U19 Idle
U01 User code 1 U20 Telecommand
... ... U21 Keyswitch
U16 User code 16 U22 Remote Reset
U17 Duress code U23 Download
U18 Control Unit U24 Virtual keypad
Keypad Event Log Displays
Keypad Meaning
AC Fail Mains supply failed
AC Restore Mains supply restored
Alarm Abort User aborted alarm
AntiMask Al Znn Anti Mask alarm on zone nn
AntiMask Rs Znn Anti Mask zone nn restored
AntiMask Tp Znn Tamper on antimask zone nn
Aux DC Fail Aux power failed
Aux DC Fail Rstr Aux power restored
Bad Checksum The control unit has detected data corruption in its memory
Batt Load Fail Battery failed load test
Batt Missing Batter disconnected
Batt Missing Rstr Battery re-connected
Burg Znn Alarm Intruder alarm on zone nn
Burg Znn Rstr Instruder alarm on zone nn restored
Codes Defaulted User access codes and installer code returned to default values
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security 9751
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji