Cooper Security i-on 16 Podręcznik Użytkownika Pobierz pdf (Strona 26)

i-on30EX

Page 22

Leaving the Installer Menu

If you wish to leave the Installer Menu at

any time.

1. Press  until the display shows the

words:.





2. Press  to leave Installer menu.

(Press  if you do not want to leave the

menu.)

The display shows:





After a delay of anywhere between a

few seconds to a few 10s of seconds

(depending on the number of expanders

fitted) the display shows the time and

date:





The system is ready for further

programming.

3. If the control unit finds a device

missing, or one with an address that has

not been added using the Installer Menu

then the display shows, for example:





The top line of the display shows the

number of new devices found, and the

number of existing devices missing

(lost). The bottom line of the display

shows the first in the list of found and

lost devices. Press  to see any other

items in the list.

4. Either: Press  to go back into Installer

Menu (so that you can go and check

that all the bus devices you have

installed are connected, powered up and

addressed correctly).

Note: To check an expander address

remove the expander’s lid and briefly press

the addressing button. The two digit display

will show the bus address for a few

seconds.

OR: Press  to make the control unit

update its internal record of devices

attached to the bus. The display shows:





5. Press  to accept the change to the

bus. (You can still press  to return to

the installer menu if you do not want to

change the number of devices on the

bus.)

Note: If you attempt to leave the Installer

Menu when a detector tamper is active then

the keypad displays a fault message telling

you which detector is causing the problem.

Press



to return to the Installer Menu.

You must either close the detector tamper

or delete it from the system before you can

leave the Installer Menu.

Important!

Saving Changes

When you make changes to the Installer

Menu the control unit holds those changes

in temporary memory until you leave the

Installer Menu. As you leave the Installer

Menu the control unit writes those changes

into a permanent store. If you remove all

power BEFORE you leave the Installer Menu

then the control unit will lose your changes.

Note that this does not apply if you restore

Factory Defaults, that change takes place

immediately.

Alerts After Leaving Installer Mode

Once you have left the Installer Menu you

may see the red LEDs around the

navigation key glowing. A common cause of

this alert is that there is no telephone line

connected to the built-in communicator. If

you do not intend to use the built-in

communicator then re-enter the Installer

Menu and disable the communicator by

setting Communications – ARC Reporting –

Call Mode to “Disabled”. See the i-on Range

Engineering Guide for more information.

Re-Entering the Installer Menu

When you enter the Installer Menu from a

keypad, the alarm system is effectively

disabled. While the system is in Installer

Menu:

Any other user trying to set the system

from a keypad will see the message

“Installer on Site”.

All PAs (including radio PAs), fire alarm

zones, 24 hour zones and tampers are

disabled.

If you have logged into the system from a

PC then the alarm system is active.

If you need to re-enter the Installer Menu:

1. Make sure the system is unset and

showing the standby screen (time and

date).

2. Key in the Installer access code. The

default Installer access code is “7890”.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 35 36

Komentarze do niniejszej Instrukcji

Brak uwag

Cooper Security i-on 16 Podręcznik Użytkownika Strona 26

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security i-on 16