Cooper Security 9751 Podręcznik Użytkownika Strona 18
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2. Programming Commands
Page 12 497096, issue 3
Value Attribute Valid for Description
X3
Double Knock
(D)
Normal Alarm
(NA)
Entry Route
(ER)
For zones with this attribute, no action is
taken on first activation. To cause an alarm,
the zone must be activated twice within a five-
minute period or remain open for longer than
10 seconds. An alarm will also occur if
another double-knock zone in any partition is
activated within five minutes of the first.
Programming a zone as "Double Knock" is a
way of reducing false alarms caused by
environmental changes but is not normally
recommended. Do not apply "Double Knock"
to radio zones with a PIR detector. The radio
PIR detector uses a lockout timer and will not
send a second activation within the Double
Knock period.
X4
Omit Allowed
(O)
All When applied to a zone, this attribute allows
the user to omit the zone when setting the
alarm. Do not allow the user to omit PA
zones.
Do not apply this attribute to an FE zone if
there is no ER zone present.
X7
The meaning of this attribute depends on the zone type:
Shock
Analyser
Sensitivity
Shock Analyser
(SA)
You can set this attribute only for a zone of
type SA, and only zones 1, 2, 3 and 4 support
this type. To set the sensitivity of a shock
sensor zone, enter a digit in the range 1 (least
sensitive) to 6 (most sensitive). You must
enter the whole sequence; for example, to set
the sensitivity to 3, press X73
Entry Timer
Number
Final Exit (FE)
Entry Route
(ER)
Forbikobler
(FB)
To select which of the four entry timers (set
up using Commands 201–4, as described on
page 66) are used for the zone, enter a digit
in the range 1 to 4. You must enter the whole
sequence; for example, to select Entry Timer
3, press X73
A Armed in
Level or
Partition A
All When applied, the zone is armed when the
user selects Level or Partition A.
B Armed in
Level or
Partition B
All When applied, the zone is armed when the
user selects Level or Partition B.
C Armed in
Level or
Partition C
All When applied, the zone is armed when the
user selects Level or Partition C.
D Armed in
Level or
Partition D
All When applied, the zone is armed when the
user selects Level or Partition D.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security 9751
Systemy kontroli dostępu bezpieczeństwa Cooper Security i-on160EX Przewodnik Instalacji
(180 strony)
(180 strony)
Systemy kontroli dostępu bezpieczeństwa Cooper Security i-on160EX Instrukcja Użytkownika
(122 strony)
(122 strony)
Systemy kontroli dostępu bezpieczeństwa Cooper Security Homelink 75 Instrukcja Użytkownika
(25 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji