Cooper Security 9751 Podręcznik Użytkownika Strona 51
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2. Programming Commands
497096, issue 3 Page 45
109: Three-way Calling (UK only)
To use three-way calling, you must make sure that the BT Network Services
Option of "three-way calling" is available on the telephone line to which the
communicator is connected.
Option
0 Three-way calling off (default).
1 Three-way calling on.
Operation: If the communicator, when triggered by the control unit,
detects Off Hook or Incoming Ringing, it sends an 80ms trigger. This
trigger represents the "R" or Recall button on a telephone and is
interpreted by the exchange as a request for a new clean line. When
the new line is available, the communicator tries to connect to the
programmed receiver number.
110: Download Mode
You can program the control unit from a PC using Downloader software. The
PC can be connected to the control unit using the telephone network or, for
the 9752 or 9853 model, locally using a cable. This command enables you to
select one of these options.
Option (not 9751)
0 Local (default for 9752 and 9853). Programs the control unit for a
cable connection.
1 Remote. Programs the control unit for a telephone connection, in
which case it will wait for and answer a call from the remote PC. You
will need to use Commands 112 and 113 to configure the connection.
Notes:
1. There is no option for this command on the 9751, which has no connector for a
local PC: 110
y
selects Remote.
2. Secure Callback does not work with this command.
3. The control unit will exit from this command if Downloader does not call within 30
minutes. Press
X
to exit before then.
111: Modem Speed (9853 only)
Use this command to set the speed of the modem inside the 9853 (built-in
communicator).
Option
0 Automatic baud selection: tries to connect at 1200 baud; if that fails,
connects at 300 baud.
1 300 baud (default).
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security 9751
Systemy kontroli dostępu bezpieczeństwa Cooper Security i-on160EX Przewodnik Instalacji
(180 strony)
(180 strony)
Systemy kontroli dostępu bezpieczeństwa Cooper Security i-on160EX Instrukcja Użytkownika
(122 strony)
(122 strony)
Systemy kontroli dostępu bezpieczeństwa Cooper Security Homelink 75 Instrukcja Użytkownika
(25 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 1.203 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji