Cooper Security M2000 Podręcznik Użytkownika Strona 102
- Strona / 180
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Engineer Menu 1-9 Engineering Manual
94
)
The AC Off Delay timer (page 63) determines how long the mains must be off
before the system generates an alert.
User – An alert generated by a mains failure will require a normal user reset.
Engineer – An alert generated by a mains failure will require an engineer or remote reset.
12 – AC Bypass:Always / Healthy / Eng / Never
Always – With this option selected, an AC Mains Fault alert will not prevent a user from
being able to set the alarm system.
Healthy – Allows a user to override an AC fail alert and set the system, but only if mains is
present.
Never – Prevents the alarm system from being set if there is an AC fail alert that needs to
be reset. If the AC Fail option is set to Engineer, the system will be able to be set only after
the alert is reset by an engineer or remote reset.
13 – Line Fail:No Rst / User / Eng
No Rst – A line fault (e.g. no dial tone present) detected by the on-board modem or by an
external communicator will cause an alert to be generated, but the alert will disappear
when the line is restored. No resetting of the alert will be required.
The on-board modem can generate a "PSTN Line Fault" only if communications from the
on-board modem to an Alarm Receiving Centre (ARC) has been enabled (see page 110).
An external communicator must connect to the LINE FLT input of the panel to signal a line
fault. The line fault alert is "ATE L.F. Single" or "ATE L.F. All" (see page 49).
User – An alert generated by a line fault will require a normal user reset.
Engineer – An alert generated by a line fault will require an engineer or remote reset.
14 – LF Bypass:Always / User / Eng
Always – With this option selected, an PSTN Line Fault alert will not prevent a user from
being able to set the alarm system.
User – Allows a user to override an PSTN Line Fault alert and set the system, but only if
there is no line fault.
Eng – Prevents the alarm system from being set if there is a PSTN Line Fault alert that
needs to be reset. If the Line Fail option is set to Eng, the system will be able to be set only
after the alert is reset by an engineer or remote reset.
15 – Supervision Fail Alert
Alert – The control unit displays a supervision failure alert.
Alarm – The control unit starts an intruder alarm
Tamper – The control unit starts a tamper alarm
The control unit also operates any outputs programmed as Supervision Failure.
16 – Reset Supervision Engineer/User
Reset when healthy – The control unit clears a supervision failure if none of the radio
zones allocated to the ward have a supervision failure.
- Contents 3
- Contents Engineering Manual 4
- Engineering Manual Contents 5
- Preface 8
- Chapter 1: Introduction 9
- Network Wiring = 4 Core 11
- Engineer’skeypad 11
- (cannot have zones 11
- Control Panel Features 13
- Compatible Devices 14
- IDNode and MIDNode 15
- System Wiring 17
- 100m max 18
- Calculating Voltage Drop 19
- Table 1. Voltage Drop 20
- Voltage Drop Example 1 20
- Example 1 21
- Example 2 21
- Installation Instructions 22
- I=360mA I=180mA I=180mA 23
- Chapter 2: Getting Started 24
- Press [Ent] To 25
- Leave Menus 25
- About the Engineer Menus 26
- Options in Engineer Menu 1 27
- Step 1 – Select Zone 29
- Step 2 – Select Zone Type 29
- User's Guide 44
- Custom Output 49
- Keypad Installation 64
- Instructions 64
- Overview 75
- Option 1-5-3 : Exceptions 76
- Option 1-5-4: Auto Sets 78
- Example: Auto Setting 82
- Option 1-7: Customising Text 86
- Confirmation On 97
- Manager's Manual 104
- Introduction 105
- Sh o w s c u rr e n t 113
- [ENT] to CONFIRM 137
- 002 LEC2S 137
- Equipment 3 137
- Confirm Devices 137
- Equipment 7 139
- Default User 1 139
- [ENT] to DEFAULT 139
- Table 6. Default Settings 141
- Equipment 9 143
- Test Display 143
- 8888888888888888 143
- Manager's 147
- Log Event Codes 148
- 2:04:1 MSNode 154
- Not Learned 154
- 1:01:1 Not Used 154
- 5. TROUBLESHOOTING 156
- Appendix A: Text Keys 159
- Start Guide 160
- To program the system 161
- Commercial with Foyer Mode 162
- To Program the system 163
- Digital Communicator 164
- To Program the Communicator 165
- Test Call 165
- Dynamic Test Call 165
- Static Test call 166
- DD243: 2004 Compliance 167
- ACPO PA Reduction Policy 168
- Engineer Quick Reference 169
- Location Of : 172
- 1,Panel 2,Keypad 172
- Index Engineering Manual 174
- Engineering Manual Index 175
- Part No: 12039336 Issue 4 180
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper Security M2000
(56 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji